www.samtec.com idss, idsd for complete speci cations see www.samtec.com?idss or www.samtec.com?idsd insulator material: black glass filled polyester plating: au over 50? (1,27?) ni or sn over 100? (2,54?) cu or 50? (1,27?) ni wire: 28 awg 7/36 stranded tinned copper temperature range: -20? to +105? (rainbow cable) -40? to +105? (gray cable) contact: becu current rating: 1a contact resistance: 10 m max lead size range: (0,56mm) .022" sq to (0,71mm) .028" sq lead insertion depth: (5,59mm) .220" to (6,22mm) .245" insertion force: (single contact only) 4oz avg. ((0,64mm) .025" sq probe) withdrawal force: (single contact only) 3oz avg. ((0,64mm) .025" sq probe) rohs compliant: ye s double full size (72 positions): (91,71) 3.650 less than 72 positions: no. positions/row x (2,54) .100 + (1,50) .059 single full size (36 positions): (91,69) 3.610 less than 36 positions: no. positions/row x (2,54) .100 + (0,48) .019 (2,54) .100 (0,76) .030 sq (9,27) .365 ref (5,08) .200 (2,54) .100 end as sem bly row option no. pins per row type strip ?02 thru ?32 ?02 thru ?36 idm = standard tail male plug ids = socket mates with: tsw, mtsw, tsm, ejh idsd mates with: tst, htst, zst idmd (double) .100" (2,54mm) idc cable idms, idmd, idss & idsd series s = single d = double (color coded cable n/a for 31 thru 36 pins/row. see ?g option.) idms (single) idsd (double) idss (single) socket or male plug on one end male plug on one end with socket on other. begin part number with idm. ?t = transfer end note: this series is non-standard, non-returnable. (0,48) .019 double full size (64 positions): (82,55) 3.250 less than 64 positions: no. positions/row x (2,54) .100 + (1,68) .066 single full size (32 positions): (81,53) 3.210 less than 32 positions: no. positions/row x (2,54) .100 + (0,71) .028 (0,46) .018 x (0,48) .019 (2,54) .100 (2,54) .100 (2,54) .100 (5,08) .200 (6,10) .240 max (3,18) .125 (for square or long tail see hcmx series) specifications idms, idmd for complete speci cations see www.samtec.com?idms or www.samtec.com?idmd insulator material: black glass filled polyester plating: au over 50? (1,27?) ni or sn over 100? (2,54?) cu or 50? (1,27?) ni wire: 28 awg 7/36 stranded tinned copper temperature range: -20? to +105? (rainbow cable) -40? to +105? (gray cable) terminal: phosphor bronze current rating: 1a rohs compliant: ye s specifications ?s = single end ?d = double end ejector header see ejh series. socket or male plug on each end f-209-1 idmd?24?s?12.00?g
www.samtec.com when mating double row connector with two single row connectors, the outer most single will be connected to conductor #1 and the inside single to conductor #2. 1/8" (3,18) 1/4" (6,35) 1/2" (12,70) 3/8" (9,53) ?t8 ?t4 ?t2 ?t3 ?x 5"max. 2"min. ?o = outside reversed option assembled length ?t ?c ?a ?p ?xx? =polarized ?r = reversed ?d ?xx? = daisy chain, double ?w ?xx? = wiring reversed daisy chain, single ?st ?x? = stripped & tinned ?s ?xx? = daisy chain single ?g = gray cable 1 2 3 specify ? for gray cable. gray cable has one red edge. idss and idms uses .100" centerline cable. idsd and idmd uses .050" centerline cable. cable is 28 awg 7/36 copper wire. standard cable is same as above except color coded. specify ?x as position. for double the same position will be polarized on both ends. (not available on idm or edm, unless transfer, then only the socket is polarized.) standard plating is selective gold over becu contact for ids; selective gold over phosphor bronze for idm. same as ? ?x except outer strip connected to conductor #2 and inside strip connected to conductor #1. 7 7 7 02 04 01 03 72 71 assembled length in inches ( 1 / 8 " ) (2 inches minimum) specify suf x from table. all dimensions are ?1/16". not available in 28 positions and higher. 4 ?b ?xx? = breakout specify ?x as number of conductors to be broken out. breakout starts with number 1 lead indicated by brown wire or red stripe. shown on top side. 5 ?rw = reversed wiring #1 wire opposite position #1. 8 ?m = middle reversed 8 requires ?sxx, ?wxx or ?dxx requires ?sxx, ?wxx or ?dxx 8 6 2 " min. 4 " minimum ?x?? 1 8 " single row connectors (idss) outer most 2 " min. 4 " minimum ?x?? 1 8 " double row connectors (idsd or idmd) outer most optional polarizing key for use with idss & idsd series. also polarizes ssw, ssq, esw & esq series. black high temperature ther mo plas tic order: part number pk-01-06 (available in wheels of six each) ?r = reversed molded-to-position idc assembles low pro le skinny side locks dual beam contacts single and double row (6,35mm) .025" square and (5,84mm) .230" length tail available call samtec for hcxx series. also available (5,84) .230 (0,64) .025 sq = tin plating (both ends) = tin idm 10" (0,25m) gold ids (-t end assembly required) = 10" (0,25m) gold idm tin ids (-t end assembly required) ? ?xx.xx? = assembled length polarizing key m o l ded -t o -p os iti o n id c assemble s low pro l e s kinny side lock s dual beam contact s s in g le and double ro w ( 6,35mm ) .025" s q uare and ( 5,84mm ) .230" l ength tail availabl e c all s amtec for h c xx s eries . idsd?24?s?05.00 idsd?05?d?04.25?s02
|
